E-Maculation
https://www.emaculation.com/forum/

Not enough memory shrinkwrap
https://www.emaculation.com/forum/viewtopic.php?f=6&t=10051
Page 1 of 1

Author:  superbwl [ Mon Feb 04, 2019 1:26 pm ]
Post subject:  Not enough memory shrinkwrap

As the title says, whenever i try to mount an .IMG file presumably made with Shrinkwrap, i get the error "Not enough memory" thrown at me constantly, even with high memory set on the application (the minimum and preferred size thing) it still doesen't work insisting that it does not have enough memory.

Even tried setting the RAM memory of the computer to the highest option available.

I'm running System 7.5.3

Author:  emendelson [ Mon Feb 04, 2019 3:01 pm ]
Post subject:  Re: Not enough memory shrinkwrap

This sometimes works: give BasiliskII LESS memory, not more. Try 4 MB or 36 MB or something in between.

Author:  superbwl [ Mon Feb 04, 2019 3:22 pm ]
Post subject:  Re: Not enough memory shrinkwrap

Hm, nope that didn't seem to work.
Even tried fiddling with shrinkwrap a little more, same error message

Author:  adespoton [ Mon Feb 04, 2019 3:39 pm ]
Post subject:  Re: Not enough memory shrinkwrap

Is the disk image and shrinkwrap on an internal disk image and not the shared drive?

Author:  superbwl [ Mon Feb 04, 2019 3:54 pm ]
Post subject:  Re: Not enough memory shrinkwrap

Yes, they're both on the same drive in which i installed System 7 on.

Author:  adespoton [ Mon Feb 04, 2019 4:54 pm ]
Post subject:  Re: Not enough memory shrinkwrap

What happens if you manually launch ShrinkWrap? It's possible the version you have may not be compatible with 7.5.3, or there may be some other issue.

Author:  superbwl [ Mon Feb 04, 2019 5:18 pm ]
Post subject:  Re: Not enough memory shrinkwrap

It launches normally without any issues, it's just when i try to extract/mount or verify the image i'm trying to install is where it gives me the memory error

Author:  adespoton [ Mon Feb 04, 2019 8:00 pm ]
Post subject:  Re: Not enough memory shrinkwrap

How big is the disk image?

Also, the format for ShrinkWrap images changed at some point; is it possible you're using ShrinkWrap 1.x and attempting to mount a 2.0 image?

Author:  superbwl [ Mon Feb 04, 2019 8:18 pm ]
Post subject:  Re: Not enough memory shrinkwrap

The disk image is 1.32 MB, i tried opening it with the only two Shrinkwraps i could find.

Version 2.1 and 3.5.2 - neither sadly worked.

Author:  adespoton [ Mon Feb 04, 2019 8:27 pm ]
Post subject:  Re: Not enough memory shrinkwrap

Hmm... 3.5.2 should work with any ShrinkWrap or Disk Copy 4 disk image. Is it possible the image is damaged?

Author:  superbwl [ Mon Feb 04, 2019 8:47 pm ]
Post subject:  Re: Not enough memory shrinkwrap

Tried double-checking by mounting another image which most likely isn't corrupted, same error message pops up however..

Author:  adespoton [ Mon Feb 04, 2019 9:15 pm ]
Post subject:  Re: Not enough memory shrinkwrap

What happens if you create a disk image with ShrinkWrap and then try to mount it?

Author:  superbwl [ Mon Feb 04, 2019 9:25 pm ]
Post subject:  Re: Not enough memory shrinkwrap

It seems to mount perfectly fine - however, it creates a .image file and not a .img, renaming the extension from .image to .img doesen't seem to affect anything, although this is most likely not the correct way of doing it.

Author:  adespoton [ Mon Feb 04, 2019 11:30 pm ]
Post subject:  Re: Not enough memory shrinkwrap

Then what you've got probably aren't ShrinkWrap images; try mounting them with Disk Copy 4.2 (or Disk Copy 6) instead. If that doesn't work either, they could be some other format; you'd do best just to save them outside BII and add them to the list of volumes to mount at boot (after your boot image). If they're any sane format, they should load that way.

Page 1 of 1 All times are UTC
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/