How to set up Appletalk in Sheepshaver Windows?

About SheepShaver, a PPC Mac emulator for Windows, MacOS X, and Linux that can run System 7.5.3 to MacOS 9.0.4.

Moderators: Cat_7, Ronald P. Regensburg, ClockWise

Post Reply
psh
Tinkerer
Posts: 47
Joined: Mon May 17, 2021 10:41 am

How to set up Appletalk in Sheepshaver Windows?

Post by psh »

I recently hanging out at BBSes and tried to download roms from classicmac.ddns.net which needed Appletalk and i dont know how to configure it
User avatar
Cat_7
Expert User
Posts: 6145
Joined: Fri Feb 13, 2004 8:59 am
Location: Sittard, The Netherlands

Re: How to set up Appletalk in Sheepshaver Windows?

Post by Cat_7 »

Please read our guide here: https://www.emaculation.com/doku.php/sh ... networking
From OpenVPN install only a tap device and then see under Tap networking and bridging in the guide.

Best,
Cat_7
psh
Tinkerer
Posts: 47
Joined: Mon May 17, 2021 10:41 am

Re: How to set up Appletalk in Sheepshaver Windows?

Post by psh »

Cat_7 wrote: Wed May 04, 2022 5:44 am Please read our guide here: https://www.emaculation.com/doku.php/sh ... networking
From OpenVPN install only a tap device and then see under Tap networking and bridging in the guide.

Best,
Cat_7
How to download openvpn?
User avatar
Cat_7
Expert User
Posts: 6145
Joined: Fri Feb 13, 2004 8:59 am
Location: Sittard, The Netherlands

Re: How to set up Appletalk in Sheepshaver Windows?

Post by Cat_7 »

psh
Tinkerer
Posts: 47
Joined: Mon May 17, 2021 10:41 am

Re: How to set up Appletalk in Sheepshaver Windows?

Post by psh »

Cat_7 wrote: Wed May 04, 2022 7:12 am https://openvpn.net/community-downloads/
OK
how to activate the tap device
User avatar
Cat_7
Expert User
Posts: 6145
Joined: Fri Feb 13, 2004 8:59 am
Location: Sittard, The Netherlands

Re: How to set up Appletalk in Sheepshaver Windows?

Post by Cat_7 »

When installed and bridged with your default network connection, you can select the tap device in the SheepShaverGUI in the Network tab at Ethernet Interface. The device will get activated as soon as you start SheepShaver.

Next, make sure to set the TCP/IP control panel in Mac OS to receive an address through DHCP.

Best,
Cat_7
psh
Tinkerer
Posts: 47
Joined: Mon May 17, 2021 10:41 am

Re: How to set up Appletalk in Sheepshaver Windows?

Post by psh »

Cat_7 wrote: Wed May 04, 2022 9:51 am When installed and bridged with your default network connection, you can select the tap device in the SheepShaverGUI in the Network tab at Ethernet Interface. The device will get activated as soon as you start SheepShaver.

Next, make sure to set the TCP/IP control panel in Mac OS to receive an address through DHCP.

Best,
Cat_7
There is no tap device on sheepshaver GUI
User avatar
Cat_7
Expert User
Posts: 6145
Joined: Fri Feb 13, 2004 8:59 am
Location: Sittard, The Netherlands

Re: How to set up Appletalk in Sheepshaver Windows?

Post by Cat_7 »

That is a quite sparse answer, not much to go on.
Can you upload some screen shots somewhere of your Windows network connections and the SheepShaverGUI while opening the ethernet interface selection list?
Then link to the screen shots here.

And also copy your sheepshaver_prefs file in your answer?

Best,
Cat_7
Post Reply